Reply I used tripple wall pipe to go through the ceiling and roof. When the stove was test fired and a fire built up to run away heat, when the sides of my cast iron stove was cherry red on the sides the tripple wall pipe was still where I could place my hand on it. But I still used a ceiling sheild and a roof mount that was up to specs. Also I learned by reseaching on the net that black pipe is made for wood stoves and the less expensive galvanized pipe usually is not. By doing research I was able to learn how to reduce that 3′ clearence to 12″. After installing the stove and fire it up to worse case point I was able to make sure it was safe and would not burn down the place. But I used the correct materials and installed them properly with the right fasteners, caulks, and in the proper way. Above all else, check to see what the manufacturer says and follow the guide lines they recommend. Take a short cut here or buy the cheaper product and it will be an expensive and possibly deadly lesson to learn. Spend a little extra and get the better products and save yourself a lot.
canyou hook up a pellet stove to an exsisting chimney
They fit together to prevent smoke or draft from entering or exiting the stove. They are available in sections with separate fittings that allow you to build almost any configuration for any wood stove. This type of stove has a round, steel flange emerging from the top that allow for easy hook-up.
Dec 07, · I guess someone had a wood stove there at one time but I never thought about using it, until recently by maybe bringing the wood pellet upstairs and hooking it up to it. I may be completely wrong, but I always was afraid to even think about hooking up a wood burner to the manufactured ceiling chimney in the living room.
See the woodstove diagrams in the image gallery. With it come images of romance, economy, family, independence, a simpler life-or at least roasting marshmallows. In many ways, burning wood is the symbol for the many things that we value in a country lifestyle. But like all of the joys that we partake in by getting involved in our sustenance, wood heat carries its duties and responsibilities.
Woodstove installation is not a trivial task. Without the necessary sheet metalworking tools, you’re more likely to end up with bandaged fingers than a custom stovepipe. Without the proper precautions, you and your family’s lives are at risk from fire. Of course, you may want to do the job yourself. Perhaps you enjoy the challenge and self-satisfaction that come from doing your own installation.
Wood stove, possible to hook up to the duct work
Pea or Nut Coal. Place one on the back of the grate, cover with coal, and light fuse. As soon as there is burning coal, plug stove into wall receptacle. Coal will be burning quickly. Take 3 or 4 briquettes and break them into smaller pieces. Place them on the grate and light with a match.
Stove Pipe is used from the top of the wood stove or freestanding fireplace to the bottom of the ceiling or wall where it will connect to class-A “high temp” chimney pipe or a masonry chimney. Follow manufacturer recommendations whenever applicable when installing a chimney system.
Posted by Julian Patrick on Jun 2, in Comments Off on Connecting a wood burning stove to a chimney Connecting a stove directly to a chimney Register plate example I begin with the more common connection methods and situations. You may already have got the message that I strongly suggest that you fit a chimney liner rather than connecting directly to a chimney. If you are not lining your chimney you need to properly smoke test the chimney Chimney Integrity Test If you are going to connect your flue pipe directly to your chimney please consult with your Building Control Officer.
You do not have to line your chimney with a chimney liner. Building regulations allow direct connection of flue pipe to chimney as long as there is no danger of the building catching fire and that the combustibles smoke are successfully taken away via the flue. Danger of the building catching fire? Essentially there should be nothing near to the stove or the flue that can catch fire. Main culprits are wooden fireplace beams but prepare to look for the unexpected. The offending wood was only discovered when our liner would not go down the chimney and we had to create a hole in the upstairs bedroom.
Had we of not lined the chimney chances are that there would have been a fire. Is the chimney suitable? Combustibles being taken away suitably draft good enough? This is a stainless steel flat sheet square with a tube sticking out from it. The square is screwed to the ceiling of the fireplace Thunderbolts are great for this.
Can You Hook Up a Pellet Stove to a Heat Pump
I recently bought a wood stove with an 8″ flue collar, and my local stove shop refuses to hook it up to my existing 6″ chimney. They say this would constitute “flue undersizing,” which they claim is a code violation. I need the installation to pass inspection for my homeowner’s insurance company, so before I decide to tackle the job myself, I need to know if this would indeed constitute a code violation.
Flue undersizing is indeed a code violation, regardless of who performs the installation. Specifically, the stovepipe, liner and chimney used to vent a wood stove must be at least as large as the exhaust opening on the stove.
Note that just because an open fire worked perfectly in a chimney it does not follow that a modern wood burner will – 0pen fires waste copious amounts of heat up a chimney whereas modern wood burners, being more efficient, put less heat up a chimney; more heat is more draft.
A wood stove basically needs its own chimney. This means specific distances from the wall, a certain r-value floor, hearth distance out from the front and sides of the wood stove, and a certain size chimney. Also for the wood stove to work properly, you need a good “draft”. This is caused by the sides of the chimney getting hot enough to cause an air flow upwards.
This in turn will draw air into the wood stove. If you don’t get a good draft, then air will not be drawn into the stove and the fire will die out. Then the chimney needs to be cleaned out once or twice a year or you may have a creosote fire which can burn through the chimney into the attic and burn down your house.
Also special stainless steel double wall chimneys are required and must be installed in a certain manner so the heat from the chimney will not be too close to any wood framing in your ceiling, attic, or roof. Again keeps your house from being burned down. Then the “clincher” is that for your wood stove to be covered by your homeowners insurance, it must be installed to code, inspected by your local building inspector, and then inspected by the insurance company.
Then they will add it to your policy and you will be covered. If you don’t install it to code and have a fire which burns down your house, then the insurance company does not have to pay a dime! When I installed my wood stove, I thought about the insurance thing and this made me decide to do it by the book. Of course installing to code pretty much makes it a safe wood stove and chimney with a low risk of fire.
You have a link proving you can’t have a cold air return in the same room as a woodstove? I find that hard to believe, considering the fact that many people have their woodstoves in their living room, and they also have a cold air return in their living rooms. Also, what about open concept houses, how is a room defined? It’s also common sense. Now, I do think if I looked even further, there might be a distance you must be from the fireplace or wood stove, but it’s best not to have a return air inlet near your solid-fuel burning appliance – ever.
Outdoor Boiler Installation Kits and,Outside Boiler Bleeder Kits alond with Plate Exchanger Installation Kits also called a Boiler Installation Kit,and also called a Water-to-Water Boiler Installation Kit. WE have Domestic Hot Water Installation Kits, Hot water heater Side Arm Installation Kits for Domestic Hot Water Water Coil Installation Kits and Water-to-air Heat Exchanger Installation.
A couple of very common questions we get from our customers are: Wood stove radiant heat off your furnace is the best type of heat and keeps your floors toasty warm! Hotter temperatures will crack the floor if you have concrete and may warp your wood if it is any hotter. One nice thing about radiant floor heat, is that it keeps the lower 10 feet of your room the warmest. This eliminates heat going up to the ceiling and out the roof where it is ultimately lost.
This is one of the reasons for the great savings with radiant floor heat. It is also very nice not having air blowing around. This means that air is not blowing around either and it ends up feeling warmer. Hydronic heat, means heat distributed via water.
Can’t find a solution to your problem? Post a question in our Forums. Woodburning furnace and chimney My husband and I are planning to install a woodburning furnace and new chimney any suggestions would be helpful. We have a two story home and want to know should the chimney go inside or out.
Jan 11, · Canyou hook up a pellet stove to an exsisting chimney? want to hook up a pellet stove,,,,can i put it in the chimney that i use for my furnace?? Follow. 3 answers 3. Can I install a pellet stove vented throught a chimney, just like a wood stove? Answer : Resolved.
Baraboo Wisconsin Ky Boy 33 said: My 6″ flue has worked great venting this stove. I can not burn it with doors open and screen in place with the 6″ flue, that is only recommended with the 8″ pipe. I wasn’t going to ever burn it that way anyway. I don’t see a problem. I have the same set up. I went to the factory and the response I received was positive as long as the doors were not open during operation.
I will get some more details and add to this when I find the correspondence. My stove is an early model I have been using all this season with no issues. My length is 21′ The bigger issue at hand may be the insurance company covering the use of a wood stove in an out building, My company State Farm would not allow it. This was my inquiry to VC Hello- the following is from an e-mail thread I sent to the manufactuer of the cimney pipe I intend to use for my Defiant Encore I just purchased as used from a private party.
The manufactuer of the stove pipe and acessories is Duravent, the product I am intending to use is the DVL double-wall oval to round adaptor model , model N ceiling support box, with model chimney adaptor and model telescoping double-wall pipe.
Stove Pipe Adapter
When connecting appliances to stovepipe things don’t always match up as well as you’d like. DuraBlack Applications – Single-wall interior stovepipe for connecting woodstoves to manufactured chimney. Materials and Construction – gauge steel construction.
A wood stove is a great way of warming a room, and if you have a fireplace flue already, then installing a wood stove onto this flue is not very difficult. A fireplace itself is not a very good conductor of heat, so you may find that a stove is the best way of using a natural product without sacrificing warmth.
Outdoor Wood Boiler From Junk Outdoor wood boilers have become a popular option in the cold country for heating the home. The advantage is that you keep all the smoke, mess, and fire danger outside and away from the house. The down side is the cost. A factory made one costs several thousand dollars. We burn wood to save money, thus the spending of several thousand doesn’t support that goal. I will show you how I built mine for almost no cost. I ran the first one of these all last winter with no problems at all.
I didnt buy a single whiff of gas for the whole winter. The Fire Box we start with the construction of the fire box. I aquired from a dumpster a large water heater that I am using for my firebox. I’ve found the round firebox works great because the flames play all around the top for good heat transfer.